PTC 6 AF Q C EJK A
Home /PTC 6 AF Q C EJK A
- B-112, Block B, Phase-2, Noida, Uttar Pradesh-201305
- Phone No. : 0120-4693000
- Email. : sales@powertecsupplies.com
Home /PTC 6 AF Q C EJK A
| Voltage | 230VAC (85 - 264VAC) single phase 50Hz |
| Current | 55A max at 85VAC. |
| Protection | Auto polarity, over current Protection by Internal fuse. U/V (< 84VAC), O/V (>265VAC) recovery auto at nominal range with 5V hysteresis. |
| Input to Output | 1000VAC 1minute cutoff current =10mA / 500VDC.20Mῼ |
| Input to Chassis | 1000VAC 1minute cutoff current =10mA / 500VDC.20Mῼ |
| Output to Chassis | 500VAC 1minute cutoff current =100mA / 500VDC.20Mῼ |
| Operating Temperature | -20 to 50°C internally thermal shutdown protected |
| Storage Temperature | -20°C to 50°C |
| Relative Humidity | 10-90% RH (Non-Condensing) |
| Cooling | Conduction Base plate cooling. If base plate temperature > 85 - 90°C power supply will shut down, recovery auto at <75 - 80°C. |
| Parameter | Output-1 | Output-2 | Output-3 |
|---|---|---|---|
| Voltage | 15VDC | 50VDC | 65VDC |
| Current | 3.3Amp | 10Amp | 50Amp |
| Ripple & Noise on PSU connector at 20MHz band with 1uf ceramic at RF Probe. | ±1% | ±1% | ±1% |
| Power | 50W | 500W | 3250W |
| Line Regulation on connector Pin | ±1% | ±1% | ±1% |
| Load regulation on connector Pin | ±1% | ±1% | ±1% |
| Output V-Adjustment (front panel window pre-set option). Current will be nominal at any voltage range. | 10-15VDC | 25 -50VDC | 45 - 65VDC |
| Over voltage limit | >18VDC | >54VDC | >68VDC |
| Over load limit | >4.0Amp | >12Amp | >52Amp |
| O/V, O/C & Short Ckt | In case of O/V & O/C Respective Output Voltage should be off and recover auto Hicc-up mode when fault condition remove. Check puls Cycle is 2Sec. |
| Fault Reporting | Fault reporting on serial port. |
| Voltage Factory Tolerance | ±1% of nominal output |
| Output On / Off Control | External LVTTL (3.5VDC) Independent logic for On / Off control. Logic=1 / High (3.5VDC) for On, Logic=0 / Low (0.0VDC) for Off. |
| Serial Port | Serial port RS422 data for input and output health status. Internal PSU temp and independent Output ports voltage and current display in BCD form. |
| Power Efficiency | >87% at full load with input 230VAC |
| Hold ON Time | 20mSec or higher |
| MTBF | 80,000Hrs |
| Ruggedized | Shock, vibration, impact proof |
| Mounting | Base plate mounting |
| Depth | 600mm |
| Width | 175mm with mounting flanges |
| Height | 65mm |
| Weight (unpacked) | < 6.8Kg |
| Material | Base plate Al, Top MS Chrome Plated and powder coated |
| Input | MS3102R-20-15P-SQG (Male) |
| Input Pins | Male 7 Pin for Input |
| Output, Data & On/off control |
MS3102R-28-12S-SQG (Female)
26 Pin for Output-1,2,3 & data |
| IP65 | Meet IP65 : In Mating condition only. |
| Mating Connector | Under user scope |
| Mating Part No |
Input-MS3106F-20-15S (Female)
Output-MS3106F-28-12P (Male) |
| Sealing | User will take care sealing in mating Pin. Mating connector is include back shell and dust cap with Sealing grommet. |
The communication via RS422 interface is based on an AK Protocol. Acknowledgement message
| Byte | Function |
|---|---|
| 1 | <STX> |
| 2 | ignored |
| 3...6 |
Function code
SXXX.... Control commands EXXX.... Setting commands AXXX.... Query commands – AAT0 for Auto data sending |
| 7 | Blank |
| 8 |
System and Logic status all, OK – 0, Any type error – 1
(MSB bit - 7)
O/P 1 on / Off status logic, PSU ON – 0, PSU OFF – 1 (bit no 4) O/P 2 on / Off status logic, PSU ON – 0, PSU OFF – 1 (bit no 3) O/P 3 on / Off status logic, PSU ON – 0, PSU OFF – 1 (bit no 2) PSU Over temp. above 90°C – 1, PSU Trip / OFF, below 85°C – 0, PSU OK (bit no 0) Bit 1, 5, 6 are blank. |
| 9 | Blank |
| 10 | O/P 1 - Over voltage status (normal condition= 0 if O/V detect=1) |
| 11 | O/P 1 - over load status (normal condition=0 if O/L detect =1) |
| 12 | O/P 2 - over voltage status (normal condition= 0 if O/V detect=1) |
| 13 | O/P 2 - over load status (normal condition=0 if O/L detect =1) |
| 14 | O/P 3 - over voltage status (normal condition= 0 if O/V detect=1) |
| 15 | O/P 3 - over load status (normal condition=0 if O/L detect =1) |
| 16 | Blank |
| 17 | Input health status (normal condition= 0 if U/V or O/V detect=1) |
| 18 | Blank |
| 19 | O/P1 – Voltage MSB |
| 20 | O/P1 – Voltage LSB |
| 21 | Blank |
| 22 | O/P1 – Current MSB |
| 23 | O/P1 – Current LSB |
| 24 | Blank |
| 25 | O/P2 – Voltage MSB |
| 26 | O/P2 – Voltage LSB |
| 27 | Blank |
| 28 | O/P2 – Current MSB |
| 29 | O/P2 – Current LSB |
| 30 | Blank |
| 31 | O/P3 – Voltage MSB |
| 32 | O/P3 – Voltage LSB |
| 33 | Blank |
| 34 | O/P3 – Current MSB |
| 35 | O/P3 – Current LSB |
| 36 | Blank |
| 37..39 | Temp value O/P in BCD format |
| 40 | <ETX> |
| Load Current (A) | Input Volt. 100V (%) | Input Volt. 200V (%) | Input Volt. 230V (%) |
|---|---|---|---|
| 0.0 | - | - | - |
| 0.8 | 69.3 | 69.3 | 68.4 |
| 1.6 | 79.0 | 79.1 | 79.2 |
| 2.4 | 82.7 | 83.5 | 83.4 |
| 3.2 | 84.0 | 85.4 | 85.4 |
| 4.0 | 84.3 | 86.2 | 86.3 |
| 4.2 | 84.4 | 86.3 | 86.4 |
| 4.6 | 84.4 | 86.5 | 86.6 |
| Load Current (A) | Input Volt. 100V (%) | Input Volt. 200V (%) | Input Volt. 230V (%) |
|---|---|---|---|
| 0.00 | - | - | - |
| 2.10 | 83.5 | 85.6 | 85.8 |
| 4.20 | 87.1 | 89.1 | 89.5 |
| 6.30 | 88.4 | 90.1 | 90.7 |
| 8.40 | 88.7 | 90.8 | 91.2 |
| 10.50 | 88.6 | 90.9 | 91.3 |
| 11.55 | 88.6 | 90.9 | 91.3 |
| Load Current (A) | Input Volt. 100V (%) | Input Volt. 200V (%) | Input Volt. 230V (%) |
|---|---|---|---|
| 0.0 | - | - | - |
| 11.7 | 83.2 | 85.8 | 85.8 |
| 23.4 | 85.4 | 87.3 | 87.8 |
| 35.0 | 85.2 | 87.5 | 87.9 |
| 46.7 | 84.6 | 87.1 | 87.5 |
| 58.4 | 83.5 | 86.4 | 86.9 |
| 64.2 | 82.9 | 86.0 | 86.5 |
